There has been an increasing amount of discussion around EMI and its negative effects on the performance of avalanche transceivers among the snow safety community. Although this is not a new topic, it is taking on a heightened level of awareness and importance as the number of winter backcountry users increases and people are carrying more personal electronic devices such as smart phones, smart watches, GPS devices, heated clothing, and electronic airbag packs.

Avalanche transceivers are essentially radios that work by communicating on an internationally accepted frequency band, 457 kHz. A transceiver in send mode transmits a signal pulse every second which is defined by ETSI EN 300 718-1. When switched into search mode, the transceiver will listen for nearby signal pulses and display distance and direction information to aid in locating transmitting transceivers (avalanche victims). The further away you get from a transmitting transceiver, the fainter the signal becomes. At the maximum useable ranges, a searching avalanche transceiver is “listening for a whisper.” It is here that the transceivers are most susceptible to EMI.  

Dans cet article de QC Lab, on va se concentrer sur les sources actives d'EMI, car elles posent souvent le plus de soucis et on peut généralement les atténuer grâce à quelques connaissances et actions de base. La plupart des appareils électroniques génèrent des EMI à différentes fréquences et avec diverses intensités. Quand les EMI se trouvent proches de la bande de fréquence 457kHz, cela peut nuire aux performances des transceivers. Garde en tête que la plupart des appareils grand public ne sont pas conçus spécialement pour les voyages en pleine nature et n'accordent pas vraiment d'importance à la bande sacrée de 457kHz.

Commençons par examiner quelques images simples d’un analyseur de spectre pour mieux comprendre les concepts. Le signal provenant d’une balise avalanche dans un environnement relativement sans bruit est illustré dans la Figure 1 ci-dessous. Un certain niveau de bruit de fond est inévitable dans le monde réel. Un environnement vraiment sans bruit ne peut être créé qu’en laboratoire. Comme tu peux le voir, le niveau du signal est nettement supérieur à celui du bruit. La différence entre ces niveaux est connue sous le nom de rapport signal sur bruit (S/N). Le rapport S/N est important car le processeur de la balise utilise ces informations pour identifier un véritable signal de balise au milieu de tout ce qui se passe.

As you get further away from the transmitting transceiver and the signal becomes weaker, it looks more like Figure 2 below. Notice the decreased signal to noise ratio.   

Les images ci-dessus montrent le signal émis par le transceiver dans un environnement relativement sans bruit. Si une interférence provenant d'un autre appareil électronique est introduite, le rapport S/N diminuera encore plus, car des pointes de bruit commenceront à noyer le signal souhaité, le rendant indistinguable. Peux-tu faire la différence entre le signal du transceiver et les pointes de bruit causées par une interférence active dans la Figure 3 ci-dessous ?

In the above image, it is much more difficult to distinguish the signal from the noise. This is the information that your beacon is trying to process. 

The presence of interference can result in reduced range, reduced reliability of directional indicators, and ghost signals. Ghost signals occur when noise spikes resemble a true transceiver signal, causing the processor to interpret them as a transmitting transceiver. This degradation in performance is intensified when operating at the far end of the transceiver’s range. 

Why does this matter to me?  

The short answer: because it can slow down your search. In an avalanche rescue scenario, when first trying to acquire a signal during the start of the coarse search, the signal to noise ratio can be very small, and any interference can be detrimental. Time is of the essence and the clock is ticking! Ghost signals and false directional arrows can send you off in the wrong direction, and waste time. Reduced range means you must reduce your search strip width as well as get closer to the buried victim before you get a reliable signal. This is when it is most important to reduce the number of EMI sources.  

What Causes Interference? 

The primary cause of EMI is other electronic devices in close proximity to the searching transceiver. In this case, distance is your friend, because EMI from an electronic device will decrease exponentially as you move it further away from your searching transceiver. 

Using this principle, the “20/50 rule” was born. We can mitigate noise by keeping EMI sources a sufficient distance away from the transceiver. The 20/50 rule was adopted across the industry to help users remember to keep electronics and other sources of interference at least 20cm (8in) away from a sending transceiver and 50cm (20in) away from a searching transceiver. If you are only going to remember one thing, and make sure your partners know it too, it should be the 20/50 rule!  

It is important to understand that this is a guideline and it in no way guarantees that all EMI will be mitigated. There are many types of electronics on the market, and some will cause interference at distances greater than 50cm. It is impossible to test all combinations, so we will focus on common personal electronics that are often found in the backcountry.  

 Okay, that’s good to know, but how much interference do electronics and other items often found in the backcountry really create? To better answer this question, the BD QA crew set out to investigate. The focus of this testing was to better understand the reduction in stable signal (a combination of range and reliability of the directional arrows). 

The Testing:

The QA crew drove out to the Bonneville Salt Flats west of Salt Lake City to find a wide-open barren space, away from as many possible sources of electromagnetic interference found in the city. 

A transceiver in send mode was placed at the end of a 100m tape measure. It was then slowly approached with a searching transceiver until a steady signal, both distance and direction indicators, was indicated. The distance at this point was then recorded. 

Various electronics often found in the backcountry were used in our test, including smart watches, GPS watches, smartphones, two-way radios, action cameras, satellite communication devices, electronic airbag packs, and even a snowmobile. The searching transceiver was held at 50cm from the torso using a static tether to help maintain the appropriate distance. Each item was then placed in a normal use position as noted below.  

The goal was to determine how bad it might be to violate the 20/50 rule. To do so, many items were held closer than 50cm (i.e., heated gloves and smart watches). Each item was tested three times, and the average taken. We then calculated the reduction in range compared to a baseline with no other items present. 

The Results

As you can see, there was a wide range of reductions in performance depending on the power of the devices, and how close they are to the searching transceiver.  

Some Caveats:  

1.) These items were tested one at a time, and it is likely that there would be a compounding effect from multiple concurrent devices.  

2.) The testing was conducted using a single pair of transceivers and a random selection of electronic devices. They do not represent every device out there. Personal electronic devices will continue to get more powerful over the coming years. 

The takeaway here is that EMI is real, and it can have a significant impact on transceiver performance! And we can’t stress enough the importance of updating the firmware of your avalanche transceivers and electronic avalanche airbag packs.  

Firmware

Transceiver and electronic airbag pack manufacturers are continually refining their firmware to improve performance (much the same way the apps on your phone are continually being updated). Firmware updates can improve features, extend battery life, reduce harmful interference being generated, and improve the way interference signals are processed.

It is of utmost importance to keep your firmware updated for these products. But we know many people do not. Don’t be one of these people. Update your firmware now. It’s easy and can often be done using an app on your phone. Refer to the manufacturer’s website for information on performing firmware updates.

Conclusions / Key Takeaways and General Guidelines

1.     Be aware of EMI.

• It’s real, and it can have a significant negative effect on transceivers.
• It will have its largest influence during initial signal acquisition, which when you really don’t want to be wasting time.
• As you get closer to the transmitting transceiver and its signal becomes stronger, interference will have less of an effect.
• You will likely not be aware of or recognize that EMI is affecting your transceiver, especially in a high-stress avalanche event.
• The more powerful and closer the electronics are to the transceiver, the more likely they are to cause significant interference.

2.     Is EMI the most important factor in your backcountry safety?

• No. Avoiding avalanche terrain, having proper training, and carrying a transceiver, shovel, probe are all higher on the list. But managing EMI is part of comprehensive backcountry safety. And in some cases, it can make a big difference, and could significantly slow down your transceiver search if not managed.

3.     Some level of EMI is unavoidable but can be kept to a minimum by having awareness of what electronics are being used and where you place them. Good practice is to discuss this with your group at the trailhead before heading out.

4.     Keep your firmware up to date on your transceiver and electronic avalanche pack.

5.     Some modern transceivers can sense the presence of interference and will provide a visual indication on the screen that your search strip width should be reduced.

6.     Like many mountain safety and risk decisions, it is your responsibility to understand your equipment and your group’s risk tolerance.

• If you want the lowest amount of interference possible, turn off all non-essential electronics and/or move away from them.
• Otherwise, follow the 20/50 rule along with some generally accepted guidelines which are shown in the graphics below.